Coleman Electric Heat pack 5 ton 230v 3ph ZE060K10B2A1AAA2A4

Description

For more info, deals, and a wide variety of equipment visit us at
https://www.heavyappliance.com/
Coleman Electric Heat pack 5 ton 230v 3ph ZE060K10B2A1AAA2A4
Weight 640 lbs
YORK® ZE/XN Series units are convertible single package
rooftops with a common roof curb for the 3, 4, 5, and 6 Ton
sizes. Although the units are primarily designed for curb
mounting on a roof, they can also be slab-mounted at ground
level or set on steel beams above a finished roof.
All ZE/XN Series units are self-contained and assembled on
rigid full perimeter base rails allowing for overhead rigging.
Every unit is completely charged, wired, piped and tested at the
factory to provide a quick and easy field installation.
All models (including those with an economizer) are convertible
between bottom and horizontal duct connections.
ZE Series units are available in the following configurations:
cooling only, cooling with electric heat, and cooling with one or
two stage gas heat. Electric heaters are available as factoryinstalled option or field installed accessory.
Features and Benefits
Standard Features
• Efficiency - The 3 thru 5 ton units reach 14.0 SEER. The
6 ton unit reaches 14.2 IEER with the standard, factoryinstalled IntelliSpeed variable frequency drive. Gas/
electric units have electronic spark ignition and power
vented combustion with steady state efficiencies of 80%.
The heat pumps reach 14 SEER and 8.0 H.S.P. F. These
efficiencies meet all legislated minimum levels and
provide low operating costs.
• DOE (Department of Energy) Compliant - All ZE models
meet minimum DOE efficiencies for cooling and fan
efficiencies. Single phase gas heating products are fan
energy rated (FER) to meet DOE requirements.
NOTE: All single phase 3 to 5 ton gas heating units are
equipped with an ECM motor on direct drive units and a
VFD on belt drive units.
• Coil Technology – All ZE condensers utilize MicroChannel “all-aluminum” condensers which provide
improved heat transfer capabilities and reduced charge
volumes. All evaporators utilize a conventional copper
tube/aluminum fin design for proven reliability and
performance.
• Convertible Airflow Design - All models (including those
with an economizer) are suitable for either bottom or
horizontal duct connections. For bottom duct, remove the
sheet metal panels from the supply and return air openings
through the base of the unit. For horizontal duct, remove
the supply and return air panels on the rear of the unit.
• System Protection - Suction line freezestats are supplied
on all units to protect against loss of charge and coil
frosting when the economizer operates at low outdoor air
temperatures while the compressors are running. Every
unit has solid-core liquid line filter-driers and high and lowpressure switches. Internal compressor protection is
standard on all compressors.
• Advanced Controls - ZE (Electric/Electric and Gas/
Electric) 3-5 ton units with no factory installed economizer
or BAS options have the option of the reliable Simplicity®
Lite™ control. All ZE models with factory installed
economizers or any BAS option and heat pump (XN) units
come with the Smart Equipment™ control system as
standard. The new unit control incorporates the best of
the already proven Simplicity® unitary controls and
creates a more robust, intelligent control. The goal of this
control is to utilize cutting edge technology making the
equipment easier to install, operate, and service. All units
are Factory commissioned, configured, and run tested.
Versatile - The Smart Equipment™ (not applicable with
units utilizing Simplicity Lite) control can be configured
to use with a standard thermostat (easy to connect
screw terminals), A zone sensor, or can be setup to
communicate with multiple BAS communication
protocols to integrate with building automation systems.
• Reduce field installed complexity - Each unit (not
applicable with units utilizing Simplicity Lite) will come
equipped with factory installed supply air, return air, and
outdoor air temperature sensors providing key
temperature readings thus reduce field installed
complexity.
• On-board USB Port - The new control (not applicable
with units utilizing Simplicity Lite) comes with a long list
of features including data logging, current and previous
system faults and software update capabilities using the
on board USB port and common flash drive. Energy use
monitoring capabilities allow custom tailoring to allow a
system to work more efficiently at all times and
occupancy levels. Self test and start-up reports also
available from the board VIA the USB port.
• Embedded LCD Display - The board (not applicable
with units utilizing Simplicity Lite) has a easy to read,
built-in LCD display and easy to use navigation joystick
and buttons allowing the user to quickly navigate the
menus displaying unit status, options, current function,
supply, return and outdoor temperatures, fault codes
and other information.
• Low Ambient - An integrated low-ambient control
allows all units to operate in the cooling mode down to
0F outdoor ambient without additional assistance.
Optionally, the control board can be programmed to
lockout the compressors when the outdoor air
temperature is low or when free cooling is available.